The Label Scraper is suitable to remove labels and sleeves of all the kinds as well as external drit from beverages bottles comes from all post consumer area. The label scraper removes labels and exernal dirt fro the beverages bottles by mechncical firiction between cutting elements on a rotating durm and fixed elements in exchangeable housing component. The Stator elements can be pre-adjuested from different bottle sizes and cabe adujst if necessary. In this section a thermal sensor has been installed constantly measuring the temperature. The crushed labels and the removed dirt are discharged off the machine together with the bottles and are separated from the material stream over a further process.
Two different design of pipe feeding -form side and -from front tilt feeding. Both multipurpose and dedicated Panchal granulators are available for recycling various plastic pipe and profile. Suitable models for smaller pipes and profiles belong to the 18″ 24″ and 30″-Series machines. Larger pipes and profiles can be fed into the 40″-Series machines. Models of the 40″-Series and 48″-Series granulate even bigger items and can be equipped with special pipe/profile in-feed hoppers to accommodate all your processing needs. The Panchal Shredder/Granulator with automatic feeding control is perfectly suited to recycling large pipe and profile.
The Panchal 600, 1000 & 1350mm in-line granulators are dedicated to the direct recycling of waste from thermoformed plastic packaging material. They cut to pieces whole foil, skeletal foil and partially punched foil into high-quality regrind at up to 1,000 lbs./hour. The granulator’s fully integrated Roll Feed System –600, 1000 & 1350mm wide – draws in continuous sheet of waste directly from the thermoforming machine. Web in-feed is automatically synchronized to match the thermoforming machine speed. The diameter of the rotor assembly is 250 mm /10″ and motor sizes of up to 20HP are available. Highly effective soundproofed encapsulation cuts noise significantly.
Panchal In-Line Recycling Plant is for In-house waste called production waste generated during production of film, tape, etc. as this machine is also capable to recycle Pre & Post consumer waste which is washed before using in process.
This machine is combination of Cutter Compactor (Densifier) + Extruder. This machine has better processing compare to traditional trend.
Extruder is available as a single-screw extruder with & Without degassing – series
NV – Non-degassing SV -Single Degassing/Vent DV – Double Degassing/Vent DHV – Double High Vacuum Degassing/Vent High-performance and flexible plastics recycling
The friction washer is made of a cylindrical trough with an inclined high speed running paddle screw to dewater and clean ground material (film flakes, granules and similar material).
The screw is fixed in the bearing housing by the means of two bearings and enclosed by a stainless steel screen. The ground material and water are fed from above at the lower end of the trough. Then the material is washed while being transported to the outlet at the top of the trough. Fines and water are thrown through the fine screen to the outside while the friction of the high-speed screw cleans the material. The drain is located at the lower end of the trough. The screen is automatically cleaned by means of a water-rinsing unit.
Sink-float tank is used for floating material like film/lables like LDPE/HDPE/PP etc on the top and at the bottom all the sink material ilke PVC/PET/PC etc. both have different Discharge point to collect different material, based on density. It is mfg. as per application and size/capacity kg/hr.
Panchal provides an ideal choice of granulators for recycling plastic waste from Film, Tape, blow molding & Injection moulded waste. Grinder can be supplied with Wet & Dry both model Wet Grinder give better cutting, less fines generation and long life blade interval.
Special Design Features:- -Mainly used for the washing of plastic film & plastic flake after shredded. -The dirty material or sands will be removed by the centrifugal force producing by the high-speed rotating of the main shaft. -The blades in the main shaft use anti-wearing steel & can be changeable. -Seperate Bearing block from Water contact -Dynamic balance rotor for sturdy run.
Sink-float tank is used for floating material like film/lables like LDPE/HDPE/PP etc on the top and at the bottom all the sink material ilke PVC/PET/PC etc. both have different Discharge point to collect different material, based on density. It is mfg. as per application and size/capacity kg/hr.
